What causes Haier Washer E1?

Drain hose blocked, kinked, crushed behind the machine, or pinched under a foot. Drain hose set at the wrong height: on machines with an internal drain pump, Haier says an upper drain outlet should sit 80 to 100 cm high, and too high stops it draining. On top loaders that drain by gravity through a lower outlet, the hose end raised above about 10 cm. Drain hose extended too long (Haier says the original hose plus any extension should be less than 3 m). Front loaders: the pump filter behind the small cover at the bottom front is clogged with lint, coins, hair pins or socks. If the hose and filter are clear, a failed drain pump, drain valve or control fault, which needs a technician.

How do I fix Haier Washer E1?

Unplug the washer before checking anything, as Haier advises. Follow the drain hose from the machine to the standpipe or sink. Straighten kinks, pull the machine forward if the hose is crushed against the wall, and clear any blockage at the hose end. Check the hose height for your type of machine: for a pumped outlet (most front loaders and many top loaders), the hose end should be 80 to 100 cm above the floor; for a lower, gravity-drain outlet, Haier says under 10 cm. Make sure the hose end isn't pushed deep into the standpipe or sitting below water in a sink. If you've added an extension hose, keep the total length under 3 m. On a front loader, put a towel and shallow tray under the pump filter cover at the bottom front, drain the water through the small emergency hose if there is one, unscrew the filter and clean it, then screw it back in tightly. Plug back in and press Start/Pause once (on a top loader, Haier also says opening and closing the lid once lets it carry on). Run a Spin or Drain program to check it empties.

When should I call a pro for Haier Washer E1?

E1 comes back with the hose straight, at the right height, and (on front loaders) a clean pump filter: Haier says to contact after-sales service. You can hear the drain pump humming but no water moves, or you hear nothing at all when it should drain, which points to the pump or its wiring. Water is left standing in the drum and the door won't unlock; drain it through the pump filter first, carefully, since the water may be hot.

Code: E1🧺 Haier Washer

Haier Washer E1 Error Code: Won't Drain or Drains Too Slowly

Q: What does Haier Washer E1 mean?

On a Haier washer, E1 is a drain error: the water didn't empty out, or emptied too slowly. Haier's fixes are almost all about the drain hose: make sure it isn't blocked, kinked or crushed, that it's at the right height for your model, and that it isn't extended past about 3 m. On front loaders, also clean the pump filter. Then press Start/Pause (or open and close the lid on a top loader) to carry on. If E1 keeps coming back with a clear hose and filter, call Haier service. Haier uses E1 for a drainage failure on both its top loaders and many of its front loaders. Haier's Australian HWT10MW2 top-loader manual lists "The machine does not drain or drain slowly. The display shows E1" with the check "Is the drain hose blocked?" and the fix "Remove the blockage. Push the Start/Pause button once." Haier India's top-load troubleshooting page adds "Is the drain hose set too high?" Haier's drain-failure article (published by Haier India and Haier Algeria) gives three reasons: on machines with a drain pump inside, the drain hose is placed too high so water drains too slowly or not at all; the hose is blocked or pressed; or the hose has been extended too long (original plus extension should be under 3 m). For front loaders, the Haier HWF75DW1/HWF85DW1 user manual lists "E1 Drainage error, water not emptied. Check drain hose for blockage and that it is properly installed," and Haier Bangladesh says drum washers can show E1 or CLr FLtr for the same drainage error, fixed by cleaning the pump filter and checking the hose. Newer Haier front loaders (like the HWF85AN1 family) show CLr FLtr instead of E1, with a 6-minute drain limit.

Reviewed 2026-10-25 · Based on 6 manufacturer & service sources

What the code means

Haier uses E1 for a drainage failure on both its top loaders and many of its front loaders. Haier's Australian HWT10MW2 top-loader manual lists "The machine does not drain or drain slowly. The display shows E1" with the check "Is the drain hose blocked?" and the fix "Remove the blockage. Push the Start/Pause button once." Haier India's top-load troubleshooting page adds "Is the drain hose set too high?" Haier's drain-failure article (published by Haier India and Haier Algeria) gives three reasons: on machines with a drain pump inside, the drain hose is placed too high so water drains too slowly or not at all; the hose is blocked or pressed; or the hose has been extended too long (original plus extension should be under 3 m). For front loaders, the Haier HWF75DW1/HWF85DW1 user manual lists "E1 Drainage error, water not emptied. Check drain hose for blockage and that it is properly installed," and Haier Bangladesh says drum washers can show E1 or CLr FLtr for the same drainage error, fixed by cleaning the pump filter and checking the hose. Newer Haier front loaders (like the HWF85AN1 family) show CLr FLtr instead of E1, with a 6-minute drain limit.

Likely causes

Drain hose blocked, kinked, crushed behind the machine, or pinched under a foot
Drain hose set at the wrong height: on machines with an internal drain pump, Haier says an upper drain outlet should sit 80 to 100 cm high, and too high stops it draining
On top loaders that drain by gravity through a lower outlet, the hose end raised above about 10 cm
Drain hose extended too long (Haier says the original hose plus any extension should be less than 3 m)
Front loaders: the pump filter behind the small cover at the bottom front is clogged with lint, coins, hair pins or socks
If the hose and filter are clear, a failed drain pump, drain valve or control fault, which needs a technician

Safe DIY checks

⚠ Before you start

Unplug the appliance (or switch off its breaker) and shut off the water supply valves before removing panels or disconnecting hoses. Keep towels handy for residual water.

Unplug the washer before checking anything, as Haier advises.
Follow the drain hose from the machine to the standpipe or sink. Straighten kinks, pull the machine forward if the hose is crushed against the wall, and clear any blockage at the hose end.
Check the hose height for your type of machine: for a pumped outlet (most front loaders and many top loaders), the hose end should be 80 to 100 cm above the floor; for a lower, gravity-drain outlet, Haier says under 10 cm.
Make sure the hose end isn't pushed deep into the standpipe or sitting below water in a sink.
If you've added an extension hose, keep the total length under 3 m.
On a front loader, put a towel and shallow tray under the pump filter cover at the bottom front, drain the water through the small emergency hose if there is one, unscrew the filter and clean it, then screw it back in tightly.
Plug back in and press Start/Pause once (on a top loader, Haier also says opening and closing the lid once lets it carry on). Run a Spin or Drain program to check it empties.

🛠 When to call a pro

E1 comes back with the hose straight, at the right height, and (on front loaders) a clean pump filter: Haier says to contact after-sales service.
You can hear the drain pump humming but no water moves, or you hear nothing at all when it should drain, which points to the pump or its wiring.
Water is left standing in the drum and the door won't unlock; drain it through the pump filter first, carefully, since the water may be hot.

Parts that commonly fix it

Always match the part number to your exact model.

⚙

Washer drain hose (or extension kit)

Replace a cracked or permanently kinked hose. Keep the total length under 3 m, as Haier advises.

Search eBay →

⚙

Drain pump

Only if the hose and filter are clear and the pump has failed. Match the part to your exact Haier model number.

Search eBay →

Sources

Last reviewed 2026-10-25. Always confirm against the manual for your exact model number.

Haier Washer E1 Error Code: Won't Drain or Drains Too Slowly

What the code means

Likely causes

Safe DIY checks

🛠 When to call a pro

Parts that commonly fix it

Washer drain hose (or extension kit)

Drain pump

Related codes

Sources