Code: F2E1🌀 Maytag Dryer

Maytag Dryer F2E1: Keypad Error (Meaning, Causes, Fixes)

Reviewed 2026-10-23 · Based on 4 manufacturer & service sources

What the code means

Maytag's Product Help article lists F2E1 as "Keypad" and gives one owner fix: turn off the dryer's circuit breaker for one minute, turn it back on, start a Timed Dry cycle and watch the dryer for one minute to make sure the code doesn't return. Maytag's service technical sheet for its electronic dryers (W10316958 Rev B) gives the detail behind it: F2E1 is a "User Interface (UI) Problem (stuck button)," meaning a button was sensed as pressed for over 20 seconds, or the user interface doesn't match the control. That sheet says this fault code appears only in Service Diagnostic mode on those models, so on some dryers you'll only see F2E1 when a technician reads the stored codes. Maytag fault codes always pair an F number (the system) with an E number (the component), and the F2 group covers the user interface: F2E2 is listed as a keypad or control problem, and F2E3 as a user interface software error. The exact meaning can vary by model, so go by the tech sheet for your model number when a technician has it.

Likely causes

Safe DIY checks

⚠ Before you start

Unplug the appliance or switch off its breaker before opening panels.

  1. Look at the control panel and take away anything resting on it or pushing a button, like a laundry basket or items on a shelf. Press each button once to check none feels stuck down.
  2. Wipe the panel gently with a soft, barely damp cloth if it's sticky, and let it dry fully before using the dryer.
  3. Reset the dryer the way Maytag describes: turn off the circuit breaker for one minute, turn it back on, start a Timed Dry cycle and watch for one minute to see whether F2E1 comes back.
  4. If the code doesn't return, use the dryer normally. A single F2E1 after a button was leaned on usually doesn't mean a part has failed.
  5. If F2E1 keeps coming back or some buttons don't respond, stop resetting it. Maytag's service steps for that open up the console, so plan on a repair.

🛠 When to call a pro

  • F2E1 returns after the one-minute breaker reset. Maytag's help page says to contact Maytag or schedule service at that point.
  • Buttons don't light or beep when pressed, or the dryer won't accept selections.
  • Running Maytag's Service Diagnostic mode and Test #6 (Buttons and Indicators), which means unplugging the dryer, removing the top panel, checking that every connector on the main control and the user interface is fully seated, and checking that the user interface is properly inserted in the console.
  • Replacing the user interface and housing assembly, which is the tech sheet's fix when the connections check out. If the display stays dark, the tech sheet has the technician check the main control's supply voltages first.
  • The dryer is still under warranty. Schedule Maytag service instead of opening the console.

Parts that commonly fix it

Always match the part number to your exact model.

⚙

User interface and housing assembly (console keypad board)

The tech sheet's fix for a repeat stuck-button fault once connections are checked. Match it to the model number on your dryer's tag.

[affiliate link slot: AFFILIATE_SLOT_UI_BOARD]
⚙

Digital multimeter

For a technician-style check of the control's supply voltages, with care and only by someone trained for live measurements.

[affiliate link slot: AFFILIATE_SLOT_MULTIMETER]

Sources

  1. Maytag Product Help: F2E1 Error Code - Dryer (Keypad; one-minute breaker reset, Timed Dry check)
  2. Maytag Product Help: F2E2 Error Code - Dryer (Keypad or Control)
  3. Maytag dryer technical sheet W10316958 Rev B (F2E1 stuck button over 20 seconds or UI mismatch, service-mode only; F/E code format; Test #6 Buttons and Indicators)
  4. Maytag Product Help: Dryer Error Codes list

Last reviewed 2026-10-23. Always confirm against the manual for your exact model number.